Design of Snap Fits

A major attraction of plastics to designers is the ease with which fast assembly mechanisms can be incorporated into the end-product. A very good example of this is the snap fit. A typical design is shown in Fig. 2.22 although there are many variations. Snap fits exploit the fact that thin plastic sections can undergo relatively large flexural deflections for a short period of time and exhibit complete recovery. The design of snap fits is straightforward and does not involve creep curves since the time-scale of the deflectionlstress is small.
The point that will be illustrated here is that in a real design situations it is necessary to choose combinations of dimensions which provide the necessary function but which do not overstress the plastic. In the following example a set of design curves are developed to show how the different combinations of dimensions might be selected.

 PLASTICS
ENGINEERING
Third Edition
R.J. Crawford, BSc, PhD, DSc, FEng, FIMechE, FIM
Department of Mechanical, Aeronautical
and Manufacturing Engineering
The Queen’s University of Belfast

  • Read more........
  • CORROSION

    Corrosion removal deals with the taking away of mass from the surface of materials by their environment and other forms of environmental attack that weaken or otherwise degrade material properties. The complex nature of corrosion suggests that the designer who is seriously concerned about corrosion review a good readable text such as Corrosion Engineering by Fontana and Greene [35.1].
    Included in this chapter are many corrosion data for selected environments and materials. It is always hazardous to select one material in preference to another based only on published data because of inconsistencies in measuring corrosion, lack of completeness in documenting environments, variations in test methods, and possible publishing errors.These data do not generally indicate how small variations in temperature or corrosive concentrations might drastically increase or decrease corrosion rates. Furthermore, they do not account for the influence of other associated materials or how combinations of attack mechanisms may drastically alter a given material’s behavior. Stray electric currents should be considered along with the various attack mechanisms included in this chapter. Brevity has required simplification and the exclusion of some phenomena and data which may be important in some applications.
    The data included in this chapter are but a fraction of those available. Corrosion Guide by Rabald [35.2] can be a valuable resource because of its extensive coverage of environments and materials.
    Again, all corrosion data included in this chapter or published elsewhere should be used only as a guide for weeding out unsuitable materials or selecting potentially acceptable candidates. Verification of suitability should be based on actual experience or laboratory experimentation. The inclusion or exclusion of data in this chapter should not be interpreted as an endorsement or rejection of any material.

    Milton G. Wille, Ph.D., P.E.
    Professor of Mechanical Engineering
    Brigham Young University
    Provo, Utah


  • Read more........
  • Polymer Categories, Acetal (POM)


    Acetal polymers are formed from the polymerization of formaldehyde. They are also known by the name polyoxymethylenes (POM). Polymers prepared from formaldehyde were studied by Staudinger in the 1920s, but thermally stable materials were not introduced until the 1950s when DuPont developed Delrin.1 Homopolymers are prepared from very pure formaldehyde by anionic polymerization, as shown in Fig. 1.4. Amines and the soluble salts of alkali metals catalyze the reaction.2 The polymer formed is insoluble and is removed as the reaction proceeds. Thermal degradation of the acetal resin occurs by unzipping with the release of formaldhyde. The thermal stability of the polymer is increased by esterification of the hydroxyl ends with acetic anhydride. An alternative method to improve the thermal stability is copoly merization with a second monomer such as ethylene oxide. The copolymer is prepared by cationic methods.3 This was developed by Celanese and marketed under the tradename Celcon. Hostaform is another copolymer marketed by Hoescht. The presence of the second monomer reduces the tendency for the polymer to degrade by unzipping.4 There are four processes for the thermal degradation of acetal resins. The first is thermal or base-catalyzed depolymerization from the chain, resulting in the release of formaldehyde. End capping the polymer chain will reduce this tendency. The second is oxidative attack at random positions, again leading to depolymerization. The use of antioxidants will reduce this degradation mechanism. Copolymerization is also helpful. The third mechanism is cleavage of the acetal linkage by acids. It is, therefore, important not to process acetals in equipment used for polyvinyl chloride (PVC), unless it has been cleaned, due to the possible presence of traces of HCl. The fourth degradation mechanism is thermal depolymerization at temperatures above 270°C. It is important that processing temperatures remain below this temperature to avoid degradation of the polymer.5 Acetals are highly crystalline, typically 75% crystalline, with a melting point of 180°C.6 Compared to polyethylene (PE), the chains pack closer together because of the shorter C O bond. As a result, the polymer has a higher melting point. It is also harder than PE. The high degree of crystallinity imparts good solvent resistance to acetal polymers. The polymer is essentially linear with molecular weights (Mn) in the range of 20,000 to 110,000.7 Acetal resins are strong and stiff thermoplastics with good fatigue properties and dimensional stability. They also have a low coefficient of friction and good heat resistance.8 Acetal resins are considered similar to nylons, but are better in fatigue, creep, stiffness, and water resistance.9 Acetal resins do not, however, have the creep resistance of polycarbonate. As mentioned previously, acetal resins have excellent solvent resistance with no organic solvents found below 70°C, however, swelling may occur in some solvents. Acetal resins are susceptible to strong acids and alkalis, as well as oxidizing agents. Although the C O bond is polar, it is balanced and much less polar than the carbonyl group present in nylon. As a result, acetal resins have relatively low water absorption. The small amount of moisture absorbed may cause swelling and dimensional changes, but will not degrade the polymer by hydrolysis.10 The effects of moisture are considerably less dramatic than for nylon polymers. Ultraviolet light may cause degradation, which can be reduced by the addition of carbon black. The copolymers generally have similar properties, but the homopolymer may have slightly better mechanical properties, and higher melting point, but poorer thermal stability and poorer alkali resistance.11 Along with both homopolymers and copolymers, there are also filled materials (glass, fluoropolymer, aramid fiber, and other fillers), toughened grades, and ultraviolet (UV) stabilized grades.12 Blends of acetal with polyurethane elastomers show improved toughness and are available commercially. Acetal resins are available for injection molding, blow molding, and extrusion. During processing it is important to avoid overheating or the production of formaldehyde may cause serious pressure buildup. The polymer should be purged from the machine before shutdown to avoid excessive heating during startup.13 Acetal resins should be stored in a dry place. The apparent viscosity of acetal resins is less dependent on shear stress and temperature than polyolefins, but the melt has low elasticity and melt strength. The low melt strength is a problem for blow molding applications. For blow molding applications, copolymers with branched structures are available. Crystallization occurs rapidly with postmold shrinkage complete within 48 h of molding. Because of the rapid crystallization it is difficult to obtain clear films.14 The market demand for acetal resins in the United States and Canada was 368 million pounds in 1997.15 Applications for acetal resins include gears, rollers, plumbing components, pump parts, fan blades, blow-molded aerosol containers, and molded sprockets and chains. They are often used as direct replacements for metal. Most of the acetal resins are processed by injection molding, with the remainder used in extruded sheet and rod. Their low coefficient of friction make acetal resins good for bearings.16 

    Modern
    Plastics
    Handbook
    Modern Plastics
    and
    Charles A. Harper Editor in Chief
    Technology Seminars, Inc.
    Lutherville, Maryland
    McGraw-Hill
    New York San Francisco Washington, D.C. Auckland Bogotá
    Caracas Lisbon London Madrid Mexico City Milan
    Montreal New Delhi San Juan Singapore
    Sydney Tokyo Toronto